Eintrag in der Universitätsbibliographie der TU Chemnitz
Volltext zugänglich unter
URN: urn:nbn:de:swb:ch1-200601279
Banik, Kaushik (M. Tech.)
Mennig, Günter (Prof. Dr.-Ing.) ; Münstedt, Helmut (Prof. Dr. rer. nat.) ; Platzer, Bernd (Prof. Dr.-Ing. habil.) (Gutachter)
Prozeßinduziertes Langzeitdeformationsverhalten von spritzgegossenen teilkristallinen Kunststoffen
Process-induced Long-term Deformation Behavior of Injection Molded Semicrystalline Thermoplastics
Kurzfassung in englisch
Injection molding is a very complex process because the polymer experiences a complex thermorheological history during molding that influences the molecular orientation, residual stresses, frozen-in free volume and crystallinity inside the part. These generally govern the final part properties. Therefore it is highly desirable to anticipate the effect of process parameters on the resulting microstructure and mechanical properties of the finished part in the long run. In the case of a semicrystalline thermoplastic part, the problem in understanding the deformation behavior arises from its two-phase structure and a tendency exists to concentrate primarily on the effect of the crystalline phase on the deformation behavior, while the contribution of the amorphous phase is less investigated. In this work, the influence of the processing parameters on the deformation behavior of injection molded semicrystalline thermoplastic parts, viz., syndiotactic Polystyrene (sPS) and Polybutylene terepthalate (PBT), has been monitored through creep. The resulting internal structures due to processing have been determined and the deformation behavior has been analyzed. It has been observed that only the rate of cooling shows a remarkable effect on the long-term viscoelastic behavior of an injection molded semicrystalline thermoplastic part as it influences not only the crystalline, but also the free volume fraction, whereas the different states of frozen-in orientations and pressure-induced densification have only a negligible effect. Besides, physical aging also plays an important role in the deformation behavior of the injection moldings which was manifested with the decrease in the tendency to creep. Therefore, it was suggested that the cooling rate during injection molding and the aging time can significantly affect the long-term deformation behavior of the injection molded semicrystalline thermoplastics. The results also showed that when no significant effect is observed in terms of short-term mechanical properties by changing the processing conditions, but while considering the long-term behavior they show a significant effect.
| Universität: | TU Chemnitz | |
| Institut: | Zentrale Fakultätseinrichtungen Maschinenbau | |
| Fakultät: | Fakultät für Maschinenbau | |
| Dokumentart: | Dissertation | |
| Betreuer: | Mennig, Günter (Prof. Dr.-Ing.) | |
| ISBN/ISSN: | 3-939382-03-5 ; 978-3-939382-03-4 | |
| URL/URN: | http://archiv.tu-chemnitz.de/pub/2006/0127 | |
| Quelle: | Schriftenreihe Kunststoffe ; 4 | |
| SWD-Schlagwörter: | Freies Volumen , Kristallinität , Spritzgießen | |
| Freie Schlagwörter (Deutsch): | Langzeitdeformationsverhalten , Molekülorientierungen , Thermoplaste , thermorheologische Vorgeschichte , physikalische Alterung | |
| Freie Schlagwörter (Englisch): | crystallinity , free volume , Injection molding , long-termdeformation behavior , molecular orientation , physical aging , semicrystalline , teilkristallin , thermoplastics , thermorheological history | |
| DDC-Sachgruppe: | Ingenieurwissenschaften | |
| Tag der mündlichen Prüfung | 16.08.2006 |
